Remove Thingpark LRR from a Tektelic Gateway - Revert basestation to factory configuration
We have a Tektelic Kona Micro gateway https://tektelic.com/catalog/kona-micro-lorawan-gateway. I was able to install Thingpark LRR package on it following this instruction https://docs.thingpark.com/thingpark-wireless/7.1/Content/BS-installation-guides/Tektelic-base-stations.htm.
Packet Loss on SF7 in the Public Network on ST32L Based ST50H Module
Hi , Greetings, I am using STM32WL based ST50H module .It is running on Lorawan Stack 1.0.3. I am facing packet loss issue on this module ,particularly when ADR shifts to SF7.I have tried high gain antenna also, but no luck. The Network shows normal Network
Gateway Kerlink iFemtocell not connect to ip 10.152.12.10 /10.152.22.10
The gateway does not connect to ip 10.152.12.10/10.152.22.10. if you set ip "lrc-dev.thingpark.com" in the Backhaul settings, the gateway connects, but the parameters from the server are not set (frequencies, turning on the radio module) https://doc
Dragino LG02 + Abeeway micro tracker V3 + AWS
Hi, I have Dragino LP02 and Abeeway micro tracker V3, i'd like to send the data to AWS. Someone can help me? Best regards
TTGO T-Beam connecrt to Ufispace
Can I use TTGO (NodeMCU Device) connect to Ufispace (Gateway)? I try to use TTGO (NodeMCU) connect to Ufispace(Gateway). Has anyone use to connect to Ufispace, Do you have code to share?
ADR in community
Hi, I have a question about the calculation of ADR. I observed that with good radio conditions the SF changes at the 6th uplink. My device is powered at night so does not talk during the day. When the device restarts the device keeps the LoraWan session
Mac Hex Decoder
Hello, We would like to be able to decode the Max Hex Message through our Mqtt broker. Where can I find the documentation to do it ? Thanks in advance,
Is it possible to configure an alert for silent devices ?
Hi, I would like to know if in community it's possible to configure an alert for devices without uplinks from hours or days ? Thanks in advance,
Difference between thingpark wireless portal and thingpark community edition
Hi, What is the difference between thingpark wirless portal and the latest thingpark community editions? Earlier thingpark wireless doesn't support authorization header while Configuring the routing profiles now we could see there is custom header option.
Cisco IXM stuck after reboot
Hi! I have a Cisco IXM gateway. I tried to install your LRR but after reboot, my gateway seems stuck and I can't do anything with it anymore. It shows the prompt "Marvell>>" when I console into it. How can this be fixed?
Sending downlink to the device
Hi, I'm able to send an uplink from the loradevice to the connection that is created on the actility platform. I would like to send a downlink to the device. Is this the right API to use to send downlinks ? "https://dx-api.thingpark.com/core/v145/api/devices/<deviceID>/downlinkMessages"
Cannot delete Gateway
Since last update i am trying to delete a Gateway and that's not possible. I get this Error An unexpected error occurred while trying to handle your request. Please retry the request and contact your administrator if this problem persists. Error details:
packet-forwarder firmware validation failed on Cisco IXM
I've installed pubkey but cannot install packet forwarder I get error packet-forwarder firmware validation failed
Abeeway LoRaWAN tracker leaving a network and then coming back... what Join behavior to expect?
What happens when an Abeeway tracker gets out-of-range of a LoRaWAN network for a long time (or the network fails for an extended time) ? How does the tracker find-out that it has become isolated, and how does it attempt to reconnect ?
Why do I see sometimes very late packets in Wireless Logger ?
Sometimes uplink packets from devices appear in wireless logger with timestamps that are way in the past, few hours or even days. How to explain this behavior ?
ThingPark compatible gateways
Where can I find ThingPark compatible gateways?
Application server with MQTT(TLS1.2) support
My application server communicates with Actility sever. My application uses MQTT(TLS1.2) protocol. Can Actility server support MQTT(TLS1.2) protocol? And How Can My application connect and communicate with Actility server?
Most Discussed Topics
Connecting Kerlink gateway to ThingPark Community
Hello, Hello, I am preparing to connect a Kerlink Wirnet iFemtoCell-Evolution gateway to the ThingPark All-in-one platform using the TAO (ThingPark All-in-One) installation process, through the Thingpark Community area. I would like to request access
Error during Downlink Encode with Custom Driver
All - I am testing my custom device driver with the community edition of ThingPark. Uplink Decoding and Downlink Decoding is working with no issues through the test tabs on the Driver Code pane. If I try to simulate Encode Downlink I see the following
Interop EU863-870, test 3.2.1 failed ( ADR on unconfirmed uplink)
Hello All, Using interop tool for AN EU863-870 device, I have a problem to run successfuly the 3.2.1 test. 1. my device is as below: 2. For the test 3.2.1, seems to test LoRaWAN "data rate backoff" 3. From "Table 9" above picture(from LoRaWAN® L2 1.0.4
Interop EU863-870, test 4.2.1.1 failed (RxParamsSetupReq)
Hello All, Using interop tool for AN EU863-870 device, I have a problem to run successfuly the 4.2.1 test. RxParamsSetup seems ok( RX1_DR_OFFSET = 0; RX2_DR = 2; RX2_FREQ = 868.5) DevStatusReq on RX1 seems ok But the test fails on DevStatusReq sent on
Tektelic Kona Macro Gateway
Hi, wanna ask on the LRR-UUID for Tektelic Gateway which is Kona Macro. I try to use the SSH to get my gateway info such ssh support@ip gateway but I dont know the password. Then I ask Tektelic, they said it has no support account and they ask to refer