Network Survey tool intermittent display of Glamos Walker
We have used the glamos walker and it has displayed in the past the data points on the network survey tool. Sometimes it does not display any data points, but does show that it has data to show in upper left corner (see attached picture 336 data points)
Interop AS923 test 4.2.1.1 failed (RxParamsSetupReq)
Hi All, Using interop for testing AS923 Singapore, we encountered a problem while running test 4.2.1.1 RxParamsSetup seems ok( RX1_DR_OFFSET = 0; RX2_DR = 2; RX2_FREQ = 923.2) DevStatusReq on RX1 seems ok But the test fails on DevStatusReq sent on RX2.
Interop EU863-870, test 1.2.2 failed ( OTAA Join Request / Join Accept )
Hi all, When I test my device, test 1.2.2 failed everytime. From the picture, we can see the fail test. You can see that the reasons for the two failures are the same, " It must have more than (6 seconds + worst case air time transmission) between two
Error during Downlink Encode with Custom Driver
All - I am testing my custom device driver with the community edition of ThingPark. Uplink Decoding and Downlink Decoding is working with no issues through the test tabs on the Driver Code pane. If I try to simulate Encode Downlink I see the following
Interop EU863-870, test 4.2.1.1 failed (RxParamsSetupReq)
Hello All, Using interop tool for AN EU863-870 device, I have a problem to run successfuly the 4.2.1 test. RxParamsSetup seems ok( RX1_DR_OFFSET = 0; RX2_DR = 2; RX2_FREQ = 868.5) DevStatusReq on RX1 seems ok But the test fails on DevStatusReq sent on
Interop EU863-870, test 3.2.1 failed ( ADR on unconfirmed uplink)
Hello All, Using interop tool for AN EU863-870 device, I have a problem to run successfuly the 3.2.1 test. 1. my device is as below: 2. For the test 3.2.1, seems to test LoRaWAN "data rate backoff" 3. From "Table 9" above picture(from LoRaWAN® L2 1.0.4
Interop US915, test 4.2.1.1 failed (RxParamsSetupReq)
Hello All, Using interop tool for AN US915 device, I have a problem to run successfuly the 4.2.1 test. RxParamsSetup seems ok DevStatusReq on RX1 seems ok But the test fails on DevStatusReq sent on RX2. The DevStatusReq is sent on Rx2 using 923.3 MHz
Interop AU915, test (2.2.5 RX2 window) failed
Hello, While testing the AU915 device with Interop Engine, the test fails at 2.2.5. The error message is: "Ignore DevStatusReq because not sent through RX2... DevStatusReq unconfirmed downlink has been queued. Device did not respond to commands sent through
Can we configure routing for an api to post location data regularly ?
So what i want to store the location data in a different database, for that i will need to get the data, as it is in objenious, it's very easy you just need to configure the routing to a new url so it posts the data regularly (you can checkout for this
what's the difference between Actility UI dashboard and Abeeway dashboard ? are they the same thing ?
Hello, I have a question, I am using Micro Abeeway Tracker V3.1, currently I am loggining from here : https://community.thingpark.io/thingpark/abeewayDeviceAnalyzer/index.php?dxprofile=community-api but i lately discrovred this UI : https://community.thingpark.io/tpe
How to get Iot-Flow tag.
As title say: I have set some tags at Iot-Flow and on some devices. I can get the tags for each device by using DX swagger but I can't find any where how I retrieve a certain IoT-flow tags. Any tips?
New Indoor Air Quality Solution
Hello Community, FYI we will be launching soon an Indoor Air Quality solution with Zenner (device maker) and Datacake (Application Provider). All details soon available on the community program solution catalog https://community.thingpark.org/iot-solutions-catalog/
Building optimized working conditions and space management strategy through IoT
Dear community members, We have worked with WMW and Sensative and built a solution to support office managers, building operators, and workspace entrepreneurs to make their workspace even more mobile and dynamic. We will show how to improve space utilization
Video Series for the Community
Dear Community Members, I would like to propose this idea of creating a series of tutorial in the community web page animated by our community members or from Actility's teams. It will be great to have a tutorial video or inspiring insights about the
Using the Thingpark Community API
Hello, I have an account with https://community.thingpark.io/tpe/ I am trying to access the API for some python scripts. With the swagger ui, I am getting the following error. { "code": 400, "message": "Bad request: Invalid client id or secret", "errorId":
User is not logged in
Hello, We are facing a problem with the use of the API. After a while of using the API we get an error message 'User is not logged in'. Before, when we had this problem we would refresh the connection but now it doesn't work anymore. Can you tell us what
MQTT Broker
Hello, Our MQTT broker no more transmitted the downlinks whereas we are well subscribed to this topic. Do you have an explanation ? THanks in advance,